An underwater, multispectral light source

Group members: Bhrugurajsinh Pradyumansinh Chudasama, Candice Murray, Anirban Chatterjee

Background

Optical Design

Underwater light sources

Absorption of light in water

Water exhibits much higher absorption of photons than air at some wavelengths of light. This can be seen in the graph below. Increasing the depth of the water increases the absorption, which can be modeled by the absorption equation $I(x)=I(x_o)*exp(-\alpha (x-x_o))$ where $\alpha$ is the absorption coefficient for water at the wavelength of interest and $I(x)$ and $I(x_o)$ are the intensities at the final and starting locations, respectively.

Scattering in water'

Methods

LED Design

Our system needs to drive 7 high brightness LEDs. We selected 6 Philips LUMILEDS series LEDs to provide 6 of the 7 wavelengths we need. The wavelengths of these LEDs have been chosen such that they are evenly spread out in the optical spectrum. We also added a UV (395nm) LED that would be used primarily for measuring fluorescence in planktons/detecting fluorescent behavior in underwater organisms.

LED specifications from the manufacturer are shown in the table below. For full LED specifications, see [1].

LED Color	Red-Orange	PC Amber	Lime	Green	Cyan	Blue
Lumens @ 350mA	72 lm	78 lm	167 lm	102 lm	76 lm	41 lm
Lumens @ 700mA	134 lm	140 lm	313 lm	161 lm	122 lm	70 lm
Efficacy @ 350mA	98 Lm/W	73 Lm/W	174 lm/W	100 Lm/W	75 Lm/W	38 Lm/W
Efficacy @ 700mA	83 Lm/W	63 Lm/W	160 lm/W	68 Lm/W	51 Lm/W	29 Lm/W
Typical Wavelength	617 nm	591 nm	567 nm	530 nm	505 nm	470 nm
Wavelength Range	610 to 620 nm	588 to 592 nm	566 to 569 nm	520 to 540 nm	490 to 515 nm	460 to 485 nm
Beam Angle	125°	120°	125°	125°	125°	125°
Recommended Operating Current	700 mA	350 mA	700 mA	700 mA	700 mA	700 mA
Maximum Rated Drive Current	700 mA	700 mA	1000 mA	1000 mA	1000 mA	1000 mA
Typical Forward Voltage	2.1 Vf	3.05 Vf	2.75 Vf	2.9 Vf	2.9 Vf	2.95 Vf
Maximum Forward Voltage	2.8 Vf	3.51 Vf	3 Vf	3.51 Vf	3.51 Vf	3.51 Vf
Thermal Resistance	8 C°/W	10.4 C°/W	6.4 C°/W	10.4 C°/W	10.4 C°/W	10.4 C°/W
Max Recommended Junction Temp	135 °C	130 °C	150 °C	150 °C	150 °C	150 °C
Operating Temperature Range	-40 to 120 °C	-40 to 110 °C	-40 to 135 °C	-40 to 135 °C	-40 to 135 °C	-40 to 135 °C
Dimensions L x W x H	4.5 x 3 x 2 mm	10 x 10 x 3.7 mm	10 x 10 x 3.7 mm	10 x 10 x 3.7 mm	10 x 10 x 3.7 mm	10 x 10 x 3.7 mm

Circuit Design

The high current requirement for these LEDs(~700mA) means that we need to use a driver circuit to drive these LEDs as micro controllers cannot sink/source more than 25mA of current. Since the brightness of these LEDs should be adjustable, we need to have some form of LED dimming capability incorporated in our system.

• • • • Digital section goes here

This brightness control was done through pulse width modulation. The system included an Atmega168 micro controller, which has six hardware pam channels. The project requirement was to drive seven LEDs. Hence one of the general purpose IO pin on the controller was programmer to emulate the hardware PWM output via software programming. The switch on the outside of the GoPro casing is used to provide interrupt to the controller. This leads to hardware debouncing issue, where the mechanical switch creates multiple glitches on the interrupt pin input. Following circuit was used to remove the glitches:

Apart from that the software debouncing was implemented in the code. When the controller receives the interrupt, it enters halts the program execution and jumps to the interrupt service routine (ISR). In the ISR, a small delay was added before servicing the interrupt.

On every interrupt the controller switches to the nest state. The program on the controller has eight states, seven states for enabling the corresponding PWM channels, and one states for switching off all the PWM channels. The PWM outputs drive the gate of the above mentioned NMOS transistors.

• • • • Digital section end

Our design uses an NMOS transistor to sink about 0.7A though a high brightness LED. By controlling the gate voltage of an NMOS device, we can control the current flowing through the LED and hence the brightness of the LED. We chose the ZVN4306A FET from Diodes Incorporated as our high current FETs. From hspice simulations, we found that, varying the gate voltage from ~1.7V to 3.3V led to a current sweep of 0.15A t 0.70A through the LEDs. This gave us ballpark estimates of the gate voltages we should be using. Since the Atmega168 cannot generate analog signals, we fed the output of the PWM pins to the gate via a resistor. This leads to low-passing the PWM signals; effectively generating an analog voltage at the gate of the FET. This is shown in the following diagrams:

Once we were satisfied with the design and had tested the system on a breadboard, we designed a 2 layer PCB for the controller in PCBExpress. Snapshots of the PCB are shown below:

References

1. H. Buiteveld and J. M. H. Hakvoort and M. Donze, "The optical properties of pure water," in SPIE Proceedings on Ocean Optics XII, edited by J. S. Jaffe, 2258, 174--183, (1994). [2]

2. K. S. Shifrin, Physical Optics of Ocean Water, American Institute of Physics, New York, (1988). [3]

3. "Optical Absorption of Water Compendium", [4]